|
Handheld Pneumatic
Strapper |
|
This
tool is a kind of fusion packaging machine. The
lapped thermoplastic packaging belt is fused by the heat produced by
friction motion; hence, it is called "friction fusion". Principle is to
use the binding tape winding product or package, then tighten and ends
by heating molten or use the material such as bag buckles connection
machine. |
|
 |
|
Product parameter: |
 |
|
Drived:: |
by air pump |
|
Size:
|
11*3.54*7.08in(28*9*18cm) |
| Air pressure: |
0.5-0.8Mpa |
| Max strap tension Max： |
3500N |
| Strapping material: |
Polyester |
| Applications: |
PET strap, PP band |
|
Function: |
Tensioning+Sealing+Cutting |
| Strapping width: |
13mm(1/2")-19mm(3/4") |
|
Strapping thickness： |
0.5(0.0196")-1.5mm(0.06") |
| Weight： |
3.8kg(8.37lb) |
|
|
Product Analysis： |
 |
 |
|
Feature: |
|
|
The lightweight body makes the use of
equipment more convenient and greatly improves safety performance. |
|
Humanized handheld design
Portable handheld design, convenient for carrying out, suitable for
packaging large objects. |
 |
 |
Gas pipe quick connect
connector
The air pipe must be connected to the air pump for gas supply. The
packaging joint is a metal type, wear-resistant, and has a long service
life.(Red is the protective cover)
|
Easy packaging operation
Press and hold the tension button with your right thumb until the
packaging tape is completely tightened, and then press and hold the
fusion button until the packaging tape blows. |
 |
|
 |
Silencing device
In order to keep the machine quiet during operation, this machine is
equipped with special noise reduction equipment (note: after the air
pump is filled with air, the machine is used without noise). |
Rewind button
After packaging is completed, press the rewind button with your right
little thumb until the packaging belt is sent down from the tensioning
wheel, and then remove the packaging machine.
|
 |
|
Principle of
Friction Instruction: |
|
1.The compressed air
will push the piston within air cylinder. The upper part of piston and
vibrating bar is connected with the rocking pin, so the vibrating bar
will press the lapped part of packaging belt when moving down.
2.There is an elliptic
hole at the center of vibrating bar. This hole is connected with the
eccentric shaft of pneumatic motor. The pneumatic motor rotates at a
high speed (10000rpm), so the vibrating bar conducts reciprocal motion
quickly. The lower part of packaging belt is fixed by the peg teeth of
fusion toothed plate, and its upper part is driven by the peg teeth of
vibrator for strenuous friction. Hence, the lapped part of packaging
belt is fused by the heat produced by friction. When the vibration timer
reaches the set time, vibration stops and fusion completes.
3.Both upper and lower
parts of the packaging belt are stuck while extruding. |
|
Gas Source
Instruction: |
|
Requirement of air pressure
The required scope of air pressure: (5.0-7.0bar)
Installation of gas source
Filter, pressure regulating valve and lubricator assembly shall be close
to the pneumatic tool. The min. inner diameter of air hose is
6.0mm(1/4). Both ends of air supply pipe should be equipped with quick
unions.
Moisture filtration
A drain valve must be mounted at the bottom of the air supply circuit's
bypass to drain once every day.
Lubrication
Pneumatic motor should be lubricated properly, and the lubricator should
be full and well regulated (a drop every 2min). |
 |
|
Product
safety precautions: |
To ensure safe production, please read the
following precautions carefully:
1.Bear in mind
"safety-foremost" principle, and operate this pneumatic tool properly;
2.Read the Manual carefully
before operation;
3.Don't dismantle safety
parts of the tool;
4.Don't tear or damage label
or mark of the product;
5.Don't put hand or other
part of your body between packaging belt and packaging tool.
|
|
Details: |
|
 |
 |
 |
|
Product display: |
 |
|
 |
 |
|
Item include：Handheld
Pneumatic Strapper*1 |
|
Item Number: 151030 |
|
You can make order
with no worry.
Any concerns just feel free to let us know, we'll reply in 24 hours in
normal condition.
Handling Time: Shipping is usually made in 1-3 business days after
payments cleared. Orders are processed from Monday-Friday; Not on the
weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty
period has expired, you can still seek for service or technical support
from us with low cost. |
