|
Details
Operation
The fried ice plug is inserted in a
dedicated ground within three hole sockets, see the voltage is normal,
and then open the "fried ice" switch, over about 2 minutes, until
the pot began to frost, then pour the
fried ice beverage, after speculation, if stick
in the pan, shovel it up, just need to
hold down "defrosting" defrost switch (each about 10 seconds to loosen
defrosting), then continue to fry ice.
If within three minutes after the
shutdown, there is a need to re-fried ice operation, first a "defrost"
operation for 10 seconds, before opening "fried ice" switch.
If it is in three minutes after the
operation, you do not need to press defrost , fried ice can simply press
the switch.
Note
1.The machine is equipped with tempered glass, prohibit the collision,
so as not to break.
2. Place the machine horizontally on a
flat surface, if the machine is placed inclined or uneven fault will
occur. Fried ice machine in the handling and movement, not to
exceed 45 degrees inclination.
3. There must be a reliable ground wire
and leakage protection switch.
4. Do not place the machine in direct sunlight, such as in set up their
stalls in the street, due awning.
5. The machine installation, should be kept out of the wind gate side
more than
500mm of space, ensure that the machine
cooling. Around 500mm of the machine
should be set aside space for ventilation.
6. When the machine is working, do not
open and touch.
7. The machine should be operated so that the voltage 110 v .
8.The machine work ambient temperature
should be below 38 ℃, material temperature should be below during
cooling 20 ℃.
9. Fried ice machine outlet, must be single-phase three-hole socket,
which must be
firmly grounded plug the on dedicated
lines by way related to the earth. Not with other
household appliances in the same outlet.
10. Do not wash the machine with water directly, used towels to wipe
cleaning.
11.It is strictly prohibited to use hot
water or hot drinks, otherwise it will increase
the load of the compressor, damage to the
compressor.
12.Every fry ice should not be too much to
five cups is appropriate, otherwise affect the freeze speed.
13. The machine can not hit, so as not to
affect the cooling performance.
14. If the juice with pan frozen to press
the defrost key, the role is to make the ice separated from pan. Defrost
button press can not exceed 10seconds
The inspection and
handling of troubleshooting
|
Malfunction |
Reason |
Methods |
|
The machine does not work |
1.If the voltage and power is
normal
2.If the power is turned on or the
insurance is blown
3.If down three minutes before
turning on power |
1.Adjusting the voltage
2.The re-plugged or replace the
fuse
3.Turn on the defroster switch for
approximately 10 seconds, or three minutes after the restart,
etc. |
|
Can not make snow melt |
1.If the
defrost switch is in position
2.The sugar of drink is not enough
|
1.Turn off
the defrost switch
2.Add sugar
|
|
Frequent automatic transfer
machine |
1.If the
voltage is normal
2.If the machine’s inlet and
outlet is blocked
3.If is it because of some reason,
the machine inlet air temperature is too high |
1.Adjusting
the voltage
2.Stay out of the wind space 200mm
or more
3.Eliminate the cause
|
|
Can not defrost |
1.Defrost
switch is broken or turned
2.The solenoid valve is broken or
turned |
1.Exchange
defrost switch or reconnect
2.The re-plugged or exchange
solenoid valve (change solenoid valve should be sent to service
points) |
How to make ice pan ice
cream (for your reference)
Step 1. Prepare fresh fruits or vegetables
Step 2. Hand-blending the
fruits/vegetable, milk and IP-Mix (provided by Ice Pan)
Step 3. Pour the mixture over Ice Pan
Step 4. Evenly spread the mixture onto ice
pan for about 30 seconds until it's freeze
Step 5. Add the desired fruits or other
sources and mix in well with the ice cream
Step 6. Once freeze and mixed well, scoop
up the ice cream into a cup and enjoy!
|
