|
|
|
4
Layers Screen Drying Cabinet
|
|
Screen
drying cabinet is
an important tool in screen printing. Several procedures need a screen
drying cabinet like degreasing screen ,coating emulsion, coating
hardener, washout and so on.This
machine gives up traditional heating pipe technique to adopt advanced
and safe flate carbon fiber heating plate. Professional design, energy
saving, safe and easy manipulation, used for drying screen ,shading
light, proofing dust and so on.
After redesign, this cabinet has a smaller
volum, will be cheaper and easier to ship than the old type. Wooden case
prevent to be damaged in transit.
* TOP 2 Layer Max screen frame size : 23"x21"(58x55cm).
* The top layer
need to put in the screen frame in vertical direction.
* Lower 2 Layer Max screen frame size : 25"x23"(62x58cm).
|
Features
-
Intelligent temp controlling system. Its temp can be adjusted
according to the heat resistance of screen mesh. When the room temp
is 77℉ (25℃), its highest temp can reach 126℉ (52℃).
-
The inside installed axial flow fan makes the hot air in
circulation, which guarantees an equal temp in cabinet and can
improve drying efficiency meanwhile. The axial flow fan (specially
used for large computer equipment) can normally be used for about
20,000 hours. It usually takes 2-4 minutes to well dry the screens
coated with the photosensitive emulsion.
-
It
adopts hierarchical (100 levels) temp-adjusting system; users can
adjust temp according to ambient temperature and different
materials. It can operate according to your set temp next time
because of its automatic memorizing function.
-
It
is wholly coated without corrosion and dandification. The drawer
type is flexible but perfect tight. All kinds of screens can be
placed and moved flatly with printed side up to guarantee the
adhesive layer smooth.
-
The heating plates are adopted the newest blade and unit type, with
double-heat, low power and high heat efficiency. At the same time,
it guarantees the temperature of machine even to make the
temperature of each floor even and accurate.
-
Total power is 800W.compared with
traditional 3000-8000W cabinet, this machine can save power 70-90%.
-
Constructed by four layers of
cabinets,4 frames below 25”x21”(64x53) can
be held at the same time, saving time, improving efficiency.
-
Inner and out sides all adopts
electrostatic spraying, professional outlook, easy to clean and no
rust.
|
|
Voltage
|
110V
|
|
Power
|
800W
|
|
Plug standard
|
US, Canada
|
|
Machine size
|
27.9”x24”x12.2” (71x61x31cm)
|
|
Packing Size
|
32.6"x27.9"x15.7" (83x71x40cm)
|
|
Net weight
|
80Lb
(36kg)
|
|
Shipping weight
|
88Lb (40kg)
|
Note: The shipping
cost is calculated by it's shipping volume.
|
|
|
Instructions
1. Turn on the switch; then the machine will indicate
“F000” and the air fan works automatically.
2. Press “+” until to “F070’
3. Place thermometer probe on the third drawer; Check the
temp after five minutes.
4. If the temp is not right in your need, you can press
“+” or “-” to increase or reduce 10 grades; Awaiting five minutes then
check the temp.
5. After adjusting the available temp, the machine will
automatically save and memory your set data.
6. It is normal that the “F” or “O” displays alternately
when the machine is working.
|
|
|
Reference data: When the room temperature is 77F (25C) or
so, close and seal all drawers, ten minutes later after you have set,
the temp indicates —
1. Set “F050”, the temp is about 93F (34C)
2. Set “F060”, the temp is about 104F (40C)
3. Set “F070”, the temp is about 115F (46C)
4. Set “F080”, the temp is about 126F (52C)
|
|
|
|
|
Item include:
1 set 110V screen printing drying
cabinet (006005)
|
|
